| Mould Model | SB-400 / SB-390 / Custom Solid Block Mould |
| Block Size | Typical: 400 × 200 × 200 mm; 400 × 200 × 150 mm; 400 × 200 × 100 mm (Custom sizes available) |
| Block Height | 50–200 mm (design-dependent reference) |
| Material / HRC | Wear-resistant alloy steel; heat-treated, HRC58–62 (reference) |
| Cavities/Cycle | 4 / 6 / 8 / 10 / 12 / 15 / 18; custom configuration (reference) |
| Machine Brand | HAWEN / HESS / MASA / ZENITH / QUADRA / other brands (subject to fit review) |
| Machine Model | QT4-15 / QT6-15 / QT8-15 / QT10-15 / QT12-15 / QT15 / QT18 / custom models (reference; fit review) |
| Pallet Size | Custom to the receiving block-making machine |
| Life (cycles) | Approx. 80,000–120,000 cycles (reference; operating conditions apply) |
| Mounting | Reviewed against machine mounting drawings |
| Certification | CE, ISO |
Specify the solid masonry profile, face reference and edge details for sample approval.
Solid concrete blocks use a compact masonry profile without the large open cores of hollow units. Where a plain or profiled face is specified, the intended appearance should be described alongside the unit dimensions. This page focuses on communicating face details and setting a useful basis for sample review.
Provide the length, width and height with a dimensioned drawing of the finished block. Mark any recess, frog, surface marking or special edge to be formed. A sample or clear photographs can explain the visual reference. The approved drawing remains the dimensional basis for manufacturing the specified tooling.
The solid-unit cavities and matching tamper arrangement follow the approved block profile. Review the layout against the machine model, pallet dimensions and available molding area. Product height, mold mounting positions and tamper alignment need to suit the receiving equipment. A decorative face should have an agreed reference before trial approval.
Check dimensions and squareness on trial units taken from several cavities. Examine corners, vertical faces and the underside for damage or inconsistent forming. Compare any decorative finish with the accepted physical sample. Final materials, inspection criteria and supply scope are confirmed in the quotation and technical documents; a face design alone does not establish finished-block structural performance.
Send your product drawing, machine details, production pallet dimensions and required layout for a configuration review.
Explore Concrete Block Molds, or contact HAWEN for a mold quotation. The quotation and approved technical documents confirm the final tooling and supply requirements.
| Parameter | Specification |
|---|---|
| Mould Model | SB-400 / SB-390 / Custom Solid Block Mould |
| Finished Block Size | Typical: 400 × 200 × 200 mm; 400 × 200 × 150 mm; 400 × 200 × 100 mm (Custom sizes available) |
| Block Height Range | 50–200 mm (design-dependent reference) |
| Mould Material / Hardness | Wear-resistant alloy steel; heat-treated, HRC58–62 (reference) |
| Cavities per Cycle / Layout | 4 / 6 / 8 / 10 / 12 / 15 / 18; custom configuration (reference) |
| Compatible Machine Brand | HAWEN / HESS / MASA / ZENITH / QUADRA / other brands (subject to fit review) |
| Compatible Machine Model | QT4-15 / QT6-15 / QT8-15 / QT10-15 / QT12-15 / QT15 / QT18 / custom models (reference; fit review) |
| Pallet Size | Custom to the receiving block-making machine |
| Mould Service Life Reference (cycles) | Approx. 80,000–120,000 cycles (reference; operating conditions apply) |
| Frame Interface Type | Reviewed against machine mounting drawings |
Reference specifications are subject to approved product and installation drawings. Match the brand and exact machine model as one reviewed configuration; QT references do not establish compatibility with every listed brand. Confirm the components receiving the stated alloy-steel treatment and the hardness measurement locations. The 80,000–120,000-cycle figure is an approximate mould service-life reference affected by machine condition, raw materials and block design; it is not a forming-time figure or a guaranteed life.
Solid block molds are developed around your required length, width, height, and shape. This provides tooling for market-specific block formats on compatible production equipment.
The number and arrangement of cavities are determined from the block dimensions and usable machine area. Each layout is evaluated against the actual production configuration.
Accurate machining defines the cavity surfaces and matching tamper components. Controlled component dimensions support consistent block shape during properly adjusted production.
Prepare a clearer mould enquiry with a product drawing, quantity context and machine information. Organise open questions so the quotation discussion can address the actual project.
Read morePlan an existing mould replacement by separating the required product dimensions from worn tooling measurements, then define the documents and changeover details to review with HAWEN.
Read more
Tel: +8618359454595
Email: sale@hwmachines.com
MP/WhatsApp: +8618359454595
Manufacturer Address:Nanan, Quanzhou City, Fujian Province, China
Mould Model
Block Size
Material / HRC
Cavities/Cycle
Mounting
Certification
HAWEN technical summary 2026-10-20
Review solid block mold face details with HAWEN using drawings and accepted samples. Confirm recesses, edges, trial appearance and the receiving machine configuration.