| Mould Model | HB-400 / HB-390 / Custom Hollow Block Mould |
| Block Size | Typical: 400 × 200 × 200 mm; 400 × 200 × 150 mm; 400 × 200 × 100 mm (Custom sizes available) |
| Block Height | 100–300 mm (design-dependent reference) |
| Material / HRC | Wear-resistant alloy steel; heat-treated, HRC58–62 (reference) |
| Cavities/Cycle | 4 / 6 / 8 / 10 / 12 / 15 / 18; custom configuration (reference) |
| Machine Brand | HAWEN / HESS / MASA / ZENITH / QUADRA / other brands (subject to fit review) |
| Machine Model | QT4-15 / QT6-15 / QT8-15 / QT10-15 / QT12-15 / QT15 / QT18 / custom models (reference; fit review) |
| Pallet Size | Custom to the receiving block-making machine |
| Life (cycles) | Approx. 80,000–120,000 cycles (reference; operating conditions apply) |
| Mounting | Reviewed against machine mounting drawings |
| Certification | CE, ISO |
Review cavity positions with the pallet, product geometry and agreed trial inspection plan.
Cavity count is an order requirement that must be considered with the hollow block geometry and production machine. A layout review brings the outside profile, internal core arrangement and production pallet into the same discussion. This page concentrates on defining the layout and inspecting trial units across its different positions.
Provide the actual block dimensions, core shapes, machine model and production pallet size. State the required cavity count and identify the approved inspection drawing. The proposed layout must suit the block geometry and machine configuration. Any increase in cavity count should also be assessed alongside filling, compaction and demolding requirements.
Matching mold-box, core and tamper components are reviewed as a complete forming arrangement. Measured machine connections are especially useful for replacement tooling on an existing line. The quotation and approved technical documents confirm the final layout, compatibility, materials and inspection scope rather than a general product page specifying a universal output.
During the agreed trial, compare outside dimensions, core positions, web continuity and block edges. Uneven filling or inconsistent compaction can show up as differences across the pallet. Keep the mix condition and machine settings with the inspection record so the observations and subsequent adjustments can be traced. Agree the sampling points before the trial begins.
Send your product drawing, machine details, production pallet dimensions and required layout for a configuration review.
Explore Concrete Block Molds, or contact HAWEN for a mold quotation. The quotation and approved technical documents confirm the final tooling and supply requirements.
| Parameter | Specification |
|---|---|
| Mould Model | HB-400 / HB-390 / Custom Hollow Block Mould |
| Finished Block Size | Typical: 400 × 200 × 200 mm; 400 × 200 × 150 mm; 400 × 200 × 100 mm (Custom sizes available) |
| Block Height Range | 100–300 mm (design-dependent reference) |
| Mould Material / Hardness | Wear-resistant alloy steel; heat-treated, HRC58–62 (reference) |
| Cavities per Cycle / Layout | 4 / 6 / 8 / 10 / 12 / 15 / 18; custom configuration (reference) |
| Compatible Machine Brand | HAWEN / HESS / MASA / ZENITH / QUADRA / other brands (subject to fit review) |
| Compatible Machine Model | QT4-15 / QT6-15 / QT8-15 / QT10-15 / QT12-15 / QT15 / QT18 / custom models (reference; fit review) |
| Pallet Size | Custom to the receiving block-making machine |
| Mould Service Life Reference (cycles) | Approx. 80,000–120,000 cycles (reference; operating conditions apply) |
| Frame Interface Type | Reviewed against machine mounting drawings |
Reference specifications are subject to approved product and installation drawings. Match the brand and exact machine model as one reviewed configuration; QT references do not establish compatibility with every listed brand. Confirm the components receiving the stated alloy-steel treatment and the hardness measurement locations. The 80,000–120,000-cycle figure is an approximate mould service-life reference affected by machine condition, raw materials and block design; it is not a forming-time figure or a guaranteed life.
Block dimensions, core shapes, and hole arrangements are customized to your drawings or samples. Wall thickness and release geometry are reviewed together to match your product requirements and production equipment.
Swedish HARDOX steel is used for the hollow block mold beams to provide wear resistance in these components. A frame reinforced by welded stiffeners helps maintain structural stability and component alignment during repeated production.
Critical wear components undergo carbonitriding and quenching, achieving a surface hardness of HRC 59–61 with an effective hardened layer of approximately 1.5 mm. This treatment helps resist abrasive wear and preserve the forming geometry.
A machine brand name is only the beginning of a fit review. Learn which mounting, locating and movement details to discuss when evaluating a mould proposal for an existing line.
Read moreEvaluate the connection between mould machining and assembly, with practical questions about drawing revisions, mating components and the manufacturing records relevant to your order.
Read more
Tel: +8618359454595
Email: sale@hwmachines.com
MP/WhatsApp: +8618359454595
Manufacturer Address:Nanan, Quanzhou City, Fujian Province, China
Mould Model
Block Size
Material / HRC
Cavities/Cycle
Mounting
Certification
HAWEN technical summary 2026-10-20
Plan hollow block mold cavity layouts with HAWEN from product drawings and pallet data. Compare trial units across cavities and confirm the receiving machine interfaces.