| Mould Model | IB-200 / IB-225 / Custom Interlocking Block Mould |
| Product Size | Typical: 200 × 100 × 60 mm; 200 × 100 × 80 mm; 225 × 112.5 × 60 mm (Custom sizes and interlocking designs available) |
| Thickness | 40–120 mm (design-dependent reference) |
| Material / HRC | Wear-resistant alloy steel; precision-machined and heat-treated, HRC58–62 (reference) |
| Cavities/Cycle | Custom to paver size, mould layout and machine specifications |
| Machine Brand | HAWEN / HESS / MASA / ZENITH / QUADRA / other brands (subject to fit review) |
| Machine Model | QT4-15 / QT6-15 / QT8-15 / QT10-15 / QT12-15 / QT15 / QT18 / custom models (reference; fit review) |
| Pallet Size | Custom to the receiving block-making machine |
| Life (cycles) | Approx. 80,000–120,000 cycles (reference; operating conditions apply) |
| Surface Finish | Face texture and edge finish specified by the approved reference |
| Certification | CE, ISO |
Use measured trial units and a laid sample to review the intended paving pattern.
A trial panel helps review how interlocking paving units fit together after forming. It complements the measurements taken from individual units by showing boundaries, spacers and repeat modules in a representative arrangement. This page focuses on defining an inspection method for the specific pattern, rather than assuming a performance rating from its appearance.
Start with the outline drawing for each unit, the intended joint spacing and the repeat dimensions. Identify the face texture, chamfers and spacers to be inspected. Where the pattern uses more than one shape or size, establish which companion units must be included in the sample and which drawing revision applies.
Measure units produced during the agreed trial, then assemble a representative section of paving with the intended joints. Inspect the transitions between different sizes and verify that the pattern repeats without accumulated mismatch. Retain dimensional results and the accepted appearance references so the approval criteria are clear for the tooling review.
Supply the exact machine model, pallet dimensions and production mix arrangement when discussing the trial. The cavity layout and upper forming components must suit the specified unit geometry and receiving equipment. Finished-product performance is assessed for the agreed materials, process and intended use; a mold specification or laid sample does not by itself establish a universal paving load rating.
Send your product drawing, machine details, production pallet dimensions and required layout for a configuration review.
Explore Paver Block Molds, or contact HAWEN for a mold quotation. The quotation and approved technical documents confirm the final tooling and supply requirements.
| Parameter | Specification |
|---|---|
| Mould Model | IB-200 / IB-225 / Custom Interlocking Block Mould |
| Finished Product Size | Typical: 200 × 100 × 60 mm; 200 × 100 × 80 mm; 225 × 112.5 × 60 mm (Custom sizes and interlocking designs available) |
| Paver Thickness Range | 40–120 mm (design-dependent reference) |
| Mould Material / Hardness | Wear-resistant alloy steel; precision-machined and heat-treated, HRC58–62 (reference) |
| Cavities per Cycle / Layout | Custom to paver size, mould layout and machine specifications |
| Compatible Machine Brand | HAWEN / HESS / MASA / ZENITH / QUADRA / other brands (subject to fit review) |
| Compatible Machine Model | QT4-15 / QT6-15 / QT8-15 / QT10-15 / QT12-15 / QT15 / QT18 / custom models (reference; fit review) |
| Pallet Size | Custom to the receiving block-making machine |
| Mould Service Life Reference (cycles) | Approx. 80,000–120,000 cycles (reference; operating conditions apply) |
| Surface Texture / Finish | Face texture and edge finish specified by the approved reference |
Reference specifications are subject to approved product and installation drawings. Match the brand and exact machine model as one reviewed configuration; QT references do not establish compatibility with every listed brand. Confirm the components receiving the stated alloy-steel treatment and the hardness measurement locations. The 80,000–120,000-cycle figure is an approximate mould service-life reference affected by machine condition, raw materials and paver design; it is not a forming-time figure or a guaranteed life.
Interlocking outlines are machined to the approved product geometry. Consistent profiles help neighboring units fit together with the intended joint arrangement.
Paver thickness, chamfers, and connecting profiles can be developed according to your specifications. The final design is checked against machine capabilities and production requirements.
The specified paver mold clearance is 0.2–0.25 mm per side between the mold box and tamper head. Precision matching maintains the intended relationship between these forming components.
Tel: +8618359454595
Email: sale@hwmachines.com
MP/WhatsApp: +8618359454595
Manufacturer Address:Nanan, Quanzhou City, Fujian Province, China
Mould Model
Product Size
Material / HRC
Cavities/Cycle
Machine Brand
Certification
HAWEN technical summary 2026-10-20
Plan interlocking paver mold trial checks with HAWEN for dimensions, joints and pattern repeat. Review physical samples against the approved paving drawings.